Home

Product Banner
Wireless LAN Access Point

UA1.065.21840-02

Compatible

Access Point

Key component of wireless network and an important device that connects the wired stations to the distribution system in a network

Feature
  • IEEE802.11b Direct Sequence high rate compatible.
  • High-Speed wireless connection, up to 11Mbps
  • Advanced Power Management for power saving mode for battery device
  • Auto fallback data rate under noisy environment
  • WEP Encryption function
  • External two fixed dipole antennas for diversity function
  • Provide one MMX connector for external optional antenna
  • Plug-and-play Installation
  • Provides roaming, best access point selection, load balancing, network traffic filtering, network management and compatibility, optional for repeater and bridging to bridging function.
 Application
  • Home networking for device sharing
  • Wireless office for extension Ethernet range
  • Mobile networking for netebook PC or PDA
  • Build system in Ad-Hoc or Infrastructure mode
  • Suitable in application for:
- difficult-to-wire environments
- temporary LANs for special projects or peak
time like in trade exhibition, meeting.. etc.
- frequently changing environments
- SOHO (Small Office and Home Office)
- Remote access to corporate network information
like with e-mail...etc.

General Specifications
Standards:           IEEE802.11b Compliant
Data Rate:           11Mbps / 5.5 Mbps / 2Mbps / 1 Mbps
                           auto fallback
Security:              Wired Equivalent Privacy (WEP)
                           Data Encryption (TBD)
Dimension:           135 x 85 x 30 mm
LED Indicators
Red color LED steady On:      Power on
Unlighted:                                no activity
Green color LED blinking:       TX/RX activity
RF LINK  Unlighted:               no link
Green color LED steady On:    radio link status
Interface
RJ-45                                     10Base-T
COM port                              RS232
 RF Specification General
Emission Type                  Direct Sequence Spread Spectrum
                                        (DSSS)
RF Frequency                   2400MHz ~ 2483.5MHz   Europe
Operating Channel            13 Channels (Europe)
Radio Chipset:                  Intersil PRISM II
Baseband Processor         HFA3861B or HFA3863
MAC Controller               MAC Atmel AT76C510
Radiation Power               13 ~ 20 dBm                                      
Transmitter
RF Output Power             12dBm
Frequency Stability           Within ± 25 ppm
Data modulation type        BPSK (1/5.5Mbps) / QPSK
(2/11 Mpbs)

Reciever
Sensitivity                          -84 dBm (Typically @11M)
(Less than 8% of FER packet sizes is 1024 bytes)

Antenna Type
Antenna Type:                    Dual Dipole Antenna with Diversity
Antenna Gain                     2 dBi max.

Memory
SRAM                               512 Kbytes
Flash                                  512 Kbytes

Power

Power Voltage                 DC 5.1 Volt ± 5%,
AC Adapter AC 100V ~ 240V
Power Consumption         5.1 Volt, 1.0A (Typical)

Configuration Function

Interface
Configure AP by using COM port (RS232)

Set Up Procedure
a) Turn off AP
b) Connection a RS232 Cable between AP and PC
c) Set up the program " COMFIG" in PC under
WINDOWS environment.
d) Run "COMFIG"
e) Turn on AP
f) Start Configuring AP

Regulation Compliance
Compliant with:
FCC Part 15 Class B, Sec. 15.247 and 15.109
ETS 300 328 and ETS 300 826, EN55022 Class B, EN60950, CE-Mark, ARIB STD-T66
MPT RCR STD 33A (Japan, Customerized)

Operating Condition

Compliance to Environmental Test

AC110V/220V System Characteristics
Anti-spontaneous:            100% / 40 msec
40% / 60 msec
30% / 20 msec
will not cause any system failure.
Frequency range               fo ±1 0% (fo=50Hz / 60Hz)
Insulation resistance          More than 10M ohm at DC 500V
Current Leakage               Less than 1 mA
Anti-excess Voltage          Feeding 48 hours 120% voltage will
not cause any system damage
Anti-line noise                  The 800 nsec duration pulse noise of
more than 1.6 kV applied either between line and line, or line and frame will not cause any system failure, or in case the system resetting occurs, it must automatically rebooted to normal operating conditions

Vibration Test

Apply products to the vibration under the frequency and amplitude 10-25 Hz 1mm in vertical direction for one and in horizontal direction for 30 minutes will not cause any products damage.

Package Drop Test

Dropping th package from the height of 50cm for each of the six(6) faces onto the hard-wood floor will not cause any product damage.

Usage Condition

Temper Range

Operating:          -0°C ~ 50°C
                          (Except RF output power and sensitivity)
Storage:             -30°C ~ 70°C

Temperature Shock
The one cycle of temperature shock is staying -30°C for 2 hours, taking 1 hour for changing temperature up to +60°C, and staying at +60°C for 2 hours, taking 1 hour for changing temperature to -30°C. The three cycles of temperature shock will not cause any product damage.

Humidity
The product can be operated under humidity 85% at 40°C for 48 hours continuously without damage

 

HomeCompanyInformationSite MapContactDistributorPriceSupportProduct ProductInformationSitemapContactDistributorPriceSupportCompany